Aircol PD 100 Castrol
Aircol PD 100 :
Castrol Aircol PD oils are a range of compressor lubricants, based upon highly refined mineral oils, which are intended for the lubrication of both reciprocating and rotary air compressors.
Application Of Castrol Aircol PD 100
Aircol PD grades are ashless oils recommended for the lubrication of rotors, bearings and gears in rotary compressors, especially the oil flooded screw type with lubricant drain cycles of up to 2000 hours under normal use. Normal use in screw type compressors is defined by a maximum air discharge temperature =/< 100?C as defined by ISO 6743-3:2003.
Aircol PD can be used for either normal or severe duty lubrication of reciprocating and rotary drip-feed air compressors, as defined by ISO 6743.
Normal duty is described as:-
- discharge temperatures =/< 165?C
- differential pressures =/< 2.5 MPa (25 bar)
- discharge pressures =/< 7.0 MPa (70 bar).
Severe Duty is described as:-
- discharge temperatures > 165?C
- differential pressures > 2.5 MPa (25 bar)
- discharge pressures > 7.0 MPa (70 bar)
Aircol PD compressor oils exhibit low carbon forming tendencies and meet the requirements of the DIN 51506 VDL classification for reciprocating compressors having air discharge temperatures up to 220?C.
Selection of the required viscosity grade should be based upon the compressor manufacturers’ recommendation. However as a general guide Aircol PD 32 and 46 are suitable for oil flooded rotary compressors, whereas Aircol PD 68 and 100 would be selected for lubricating the crankcase and cylinders of reciprocating compressors. Aircol PD 150 is recommended for sliding-vane compressors, or for reciprocating units at high ambient temperatures.
The Aircol PD range is fully compatible with nitrile, silicone and fluropolymer seal materials.
Aircol PD is classified as follows:
- DIN 51506 classification - VDL
- ISO 6743/3 - DAA and DAB for reciprocating air compressors, DAG for rotary air compressors
Aircol PD meets the requirements (for appropriate viscosity grade) of major compressor manufacturers such as Atlas Copco, Champion, Sullair, Compair/Broomwade, Ingersoll-Rand, Kaeser and Bauer.
Advantages Of Aircol PD 100
- Good water separation characteristics allows condensation to readily separate from the oil, minimising the risk of emulsions which could block the oil separator element.
- Fully inhibited against corrosion which enables protection even when operating under humid conditions.
- Good thermal stability, low volatility and low carbon formation reduces the risk of fire and explosion and leads to a longer operating life (up to 2000 hours).
- Low deposit forming tendencies extends oil change intervals and provides longer air filter life which contributes to a reduction in maintenance costs.
- Excellent coalescing properties mean little carry over of oil in the air stream.
Additional Information Of Aircol PD 100
Castrol Aircol PD compressor oils are available in a wide range of viscosities, to suit different types of compressors operating in varying ambient temperatures. Selection of the required viscosity grade should be based upon the compressor manufacturers recommendations for the appropriate ambient temperature range, which will have been chosen to provide the best compromise between maintaining a fluid film between the working surface and minimising the amount of power absorbed by fluid friction in this oil film
Typical Characteristics Of Aircol PD 100
| Name | Method | Units | 32 | 46 | 68 | 100 | 150 |
|---|---|---|---|---|---|---|---|
| Density @ 15°C / 59°F | ISO 12185 / ASTM D4052 | kg/m³ | 870 | 880 | 880 | 890 | 890 |
| Kinematic Viscosity @ 40°C / 104°F | ISO 3104 / ASTM D445 | mm²/s | 32 | 46 | 68 | 100 | 150 |
| Kinematic Viscosity @ 100°C / 212°F | ISO 3104 / ASTM D445 | mm²/s | 5.6 | 6.7 | 8.6 | 11.4 | 14.5 |
| Viscosity Index | ISO 2909 / ASTM D2270 | - | 110 | 100 | 100 | 98 | 98 |
| Foam Sequence I - tendency / stability | ISO 6247 / ASTM D892 | ml/ml | 30/0 | 30/0 | 30/0 | 30/0 | 30/0 |
| Flash Point - open cup method | ISO 2592 / ASTM D92 | °C/°F | 226/ | 232/ | 232/ | 253/ | 256/ |
| 439 | 450 | 450 | 487 | 493 | |||
| Pour Point | ISO 3016 / ASTM D97 | °C/°F | 3.5 | 3.5 | 3.5 | -1.2 | -0.5625 |
| Water Separation @ 54°C / 129°F (40/37/3) | ISO 6614 / ASTM D1401 | min | 15 | 15 | 15 | - | - |
| Water Separation @ 82°C / 180°F (40/37/3) | ISO 6614 / ASTM D1401 | min | - | - | - | 20 | 20 |
| Rust test - synthetic seawater (24 hrs) | ISO 7120 / ASTM D665B | - | Pass | Pass | Pass | Pass | Pass |
| Carbon residue - Conradson test - after air ageing | DIN 51352-2 | %wt | 0.7 | 0.7 | 0.7 | <3.0 | <3.0 |
| Oxidation Stability - Rotating Pressure Vessel test | ASTM D2272 / IP 229 | min | 270 | 270 | 270 | - | - |
If you wish to buy Aircol PD 100 of Castrol from Mumbai, India then please email to sales@lubeoilcompany.com or call / whatsapp +919870666888.
Aircol PD 100, Castrol in India
We can give you the best cost prices to buy Aircol PD 100compared to all dealers, suppliers, vendors, wholesalers, retailers, traders, resellers and distributors in Mumbai, Navi Mumbai, Bhiwandi, Thane in Maharashtra and all India.
Air Compressor Lubricants Aircol PD 100, Castrol in India
We can also ship Aircol PD 100 to all these states of India Andhra Pradesh, Arunachal Pradesh, Assam, Bihar, Chhattisgarh, Goa, Gujarat, Haryana, Himachal Pradesh, Jharkhand, Karnataka, Kerala, Madhya Pradesh, Maharashtra, Manipur, Meghalaya, Mizoram, Nagaland, Odisha, Punjab, Rajasthan, Sikkim, Tamil Nadu, Telangana, Tripura, Uttar Pradesh, Uttarakhand, West Bengal, Andaman and Nicobar Islands, Chandigarh, Dadra and Nagar Haveli and Daman and Diu, Delhi, Jammu and Kashmir, Ladakh, Lakshadweep, and Puducherry.
